Arrington Performance is moving to Brighton, Michigan!

All new installations will be performed at our shop in Brighton -- with the same great service and Mopar mastery. In the meantime, we know we have been hard to reach on the first try. Please be patient -- your business is important to us and we are getting back to those messages as quickly as we can.
The easiest way to make sure your message is captured is to email us at sales@shophemi.com. Thank you.

DId you know about our Hellcat 426 short block?
Need 1000HP? - here you go.
TRAKit at Ultimate Street
Car Challenge in NOLA!
Arrington Powered.

Watch the Arrington Performance Intro    

LX Fuel Hose Kit 5.7L & 6.1L Charger, Magnum, & 300C 2005-2008

MSRP:$103.94
SKU:RUS-651107
Dimensions:12 x 12 x 12
Weight:1.0 lbs
Installation Skill Rating:
Manufacturer:Russell (Edelbrock)
Russell (Edelbrock)
Price: $79.95
Quantity:
Russell Performance LX Fuel Hose Kit:
Replace your OEM Dodge or Chrysler fuel lines with this Russell preassembled stainless steel braided hose kit. Fits 5.7 and 6.1 LX Dodge Charger, Dodge Magnum, and Chrysler 300c. These lines provide better flow and are a great way to dress up your engine bay. Note: the above image is for illustrative purposes only, the kit your receive may be different. 

Installation Instructions:
1. Disconnect negative cable from battery in the trunk of thevehicle and wait for fuel pressure to drop.

2. Remove engine cover by pulling upwards (The engine coveris retained by rubber grommets).

3. Remove the factory push-on type fuel fitting on the fuel railby depressing the plastic clips located on the sides of thefuel fitting (Figure 1). Use shop rags to catch any fuel thatmight spill from the fuel fitting removal process.

4. Remove the fuel hose from the hard tube line located on thechassis by using a fuel disconnect tool. (Figure.2) Use shoprags to catch any fuel that might spill from the fuel hoseremoval process.

5. Ensure that the Russell EFI push-on fittings are properlytightened on the Russell fuel hose assembly. Install Russellfuel hose assembly on the vehicle with the 5/16” fitting(smaller of the two) on the chassis side and the 3/8” fittingon the fuel rail side. Push on the Russell EFI fittings until theplastic clip is fully seated on the fuel supply tube and thefuel rail tube. Tug on the push-on fittings to ensure a properconnection. (Figure 3).

6. Once the Russell Hose has been installed, reconnect thenegative battery cable and turn the ignition key to the “on”position to allow fuel pressure to build. Start the vehicle andlet idle while watching for fuel leaks.

7. Re-install the engine cover.
 
Specs
  • Engineered to replace stock fuel hoses (Complete and ready to go)
  • Built with Russell stainless steel hoses, and anodized aluminum hose ends
  • Easily connect to OE components for maximum reliability & professional install
  • The SS outer braid hoses resist abrasion and corrosion and CPE synthetic rubber hose is compatible with all hydrocarbon and alcohol based fuels
Fits
  • Dodge Charger RT 5.7L & 6.1L SRT8 LX 2006 to 2008
  • Dodge Magnum RT 5.7L & 6.1L SRT8 LX 2005 to 2008
  • Chrysler 300c RT 5.7L & 6.1L SRT8 LX 2005 to 2008
 
Product Rating: (0.00)   # of Ratings: 0   (Only registered customers can rate)

There are no comments for this product.
 
Additional Options:
Share:
Popular HEMI Performance Parts: